Hubbardton-forge 207720 Bedienungsanleitung PDF herunterladen

Installation Instructions B221

For Wall Sconce 20-7710 & 20-7720 Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

26493

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Fixture Assembly

B Wall Mount Bracket

C Anchors (4)

D #10 Screws (4)

E #8 Black Screws (4)

F Green Ground Screw

G Cupped Washer

Caution: Be sure power is off at the main breaker

box prior to installation.

1. Center the wall mount bracket (B) over the

electrical box being sure to hold it plum and

level. With a pencil, mark the location of all

mounting holes in the wall mount bracket on

the wall behind.

IMPORTANT: Wall mount bracket must be

secured to a solidly mounted electrical box

and/or a framing member in at least two locations. Do not

depend on drywall anchors alone to support this fixture. If in

doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,

place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight

hammer.

2. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten

or strip the anchors.

3. Thread the black # 8 screws (E) up through the hole in the top of the wall mount bracket (B). Leave the bottom

screw out for now.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or

green to bare copper or green). Ground the mounting bracket using the green ground screw (F) and cupped washer

(G) to secure a pigtail lead to the bracket.

5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screw in the top of the wall bracket go through the hole in the top of the fixture. Secure the

fixture by threading the remaining black #8 screws (E) up through the hole in the bottom of the fixture and into

the mounting bracket.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

1 2

Inhaltsverzeichnis

Seite 1

Installation Instructions B221 For Wall Sconce 20-7710 & 20-7720 Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 82

Seite 2

Installation Instructions B221 For Wall Sconce 20-7710 & 20-7720 Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 82

Verwandte Modelle: 207710

Kommentare zu diesen Handbüchern

Keine Kommentare

Hubbardton-forge 207720 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Hubbardton-forge 207720 herunter. Hubbardton Forge 207720 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Verwandte Modelle: 207710

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Hubbardton-forge 207720